Description
Johnson/Evinrude Cylinder Head Bolt Set 307267 / 0307267
The Johnson/Evinrude Cylinder Head Bolt is used to secure the cylinder head to the crankcase on many OMC outboard engines.
For the SST-45 / Formula Light powerhead, the factory parts catalog specifies 10 of these bolts per engine, making this set a complete replacement set for the cylinder head.
The same bolt was also used across a wide range of standard Johnson/Evinrude outboards, so it is useful for both stock-engine repairs and racing applications.
What the Cylinder Head Bolts Do
The cylinder head bolts provide the clamping force that holds the cylinder head tightly against the head gasket and cylinder block.
Proper clamping is critical for maintaining:
- Combustion-chamber sealing
- Head-gasket compression
- Cooling-passage sealing
- Even cylinder-head loading
- Proper cylinder-head alignment
If the bolts do not clamp evenly or the threads are damaged, the head gasket may not seal correctly.
Stock Johnson/Evinrude Applications
Part number 307267 / 0307267 was used as a cylinder head screw on many Johnson/Evinrude outboards over a broad horsepower range.
Because OMC reused this fastener on many different engine families, the quantity required depends on the specific engine.
For example, some larger multi-cylinder engines use substantially more than 10 bolts.
Always verify the original part number and required quantity when ordering for a standard production engine.
SST-45 / Formula Light Application
This makes a 10-piece 307267 bolt set the correct quantity for servicing the SST-45 cylinder head.
For racers, replacing questionable head bolts during a head-gasket change or powerhead rebuild can help eliminate one more potential sealing problem.
At Liquid Revolutions, we consider the cylinder head hardware part of the complete sealing system rather than looking only at the gasket itself. A good head gasket cannot compensate for damaged threads, corroded bolts, or uneven clamping.
When Should Cylinder Head Bolts Be Replaced?
Inspect the bolts whenever the cylinder head is removed.
Replacement should be considered when you find:
- Corroded threads
- Rust or heavy oxidation
- Damaged hex heads
- Stretched or distorted bolts
- Pitting
- Damaged thread engagement
- Bolts that do not thread smoothly
- Evidence of previous over-tightening
Bolts exposed to saltwater engines deserve especially close inspection because corrosion can weaken the threads or make proper torque difficult to achieve.
Why Even Clamping Matters
A cylinder head must be pulled down evenly against the block.
Uneven clamping can contribute to:
- Head-gasket leakage
- Combustion leakage
- Cooling-water leakage
- Head distortion
- Hot spots
- Loss of compression
Always follow the correct tightening sequence and torque specification for the engine being serviced rather than tightening the bolts randomly.
Related Cylinder Head Components
When replacing the head bolts, inspect the rest of the cylinder-head assembly at the same time.
On an SST-45 engine, related parts include:
- Cylinder Head
- Cylinder Head Gasket
- Cylinder Head Bolts
- Cylinder block sealing surface
- Cooling passages
- Spark plugs
The SST-45 rules allow both 325602 and 325603 cylinder-head castings, so the bolt set can be used with either legal head when the rest of the assembly matches the required configuration.
Installation & Service Tips
Before installing the cylinder head:
- Clean the block and head sealing surfaces
- Inspect the head for warpage or damage
- Clean the bolt holes
- Inspect crankcase threads
- Check every bolt for damaged threads
- Install the correct head gasket
- Follow the proper tightening sequence
- Torque the bolts to the correct specification for the engine
Do not use bolt torque alone to compensate for a warped head or damaged gasket surface.
Key Features & Benefits
- Complete 10-Bolt SST-45 Set – Correct quantity for the SST-45 / Formula Light cylinder head
- Secures Cylinder Head to Block – Provides the clamping force needed for proper head-gasket sealing
- Stock & Racing Applications – Used on both standard OMC outboards and SST-45 powerheads
- Ideal for Rebuilds – Useful during head-gasket replacement or complete powerhead service
- Works With SST-45 Legal Heads – Compatible with the 325602 and 325603 cylinder-head configurations when properly applied
Because this bolt was used on many different OMC engines, not every application uses 10 pieces

