Description
Johnson/Evinrude Fuel Pump Filter Screen 0312675 – Help Protect the Fuel Pump & Carburetors
The Fuel Pump Filter Screen is used on select OMC, Johnson and Evinrude outboard engines as the internal filter screen located beneath the fuel pump or filter cap.
Its job is simple but important: help catch dirt, debris, and other contaminants before they continue through the fuel system toward the carburetors.
OEM fuel pump diagrams identify 312675 as the “Screen, Filter” or “Screen, Cap”, typically with 1 screen used per applicable fuel pump assembly.
What the Fuel Pump Filter Screen Does
Fuel entering the engine may carry small amounts of debris from:
- Fuel tanks
- Fuel hoses
- Connectors
- Older fuel-system components
- Contaminated fuel
- Deteriorating hose material
The screen provides an additional filtering point before fuel travels farther through the pump and carburetor system.
A clean filter screen helps support:
- Consistent fuel flow
- Reliable fuel-pump operation
- Cleaner carburetor fuel passages
- Stable engine performance
- Reduced risk of debris reaching jets and needles
Common Signs of a Dirty or Restricted Fuel Screen
A restricted filter screen may contribute to:
- Hard starting
- Engine hesitation
- Poor acceleration
- Engine surging
- Reduced top-end RPM
- Fuel starvation under load
- Engine running normally at low RPM but falling off at higher RPM
- Difficulty maintaining wide-open throttle
- Inconsistent fuel delivery
A dirty screen is not the only possible cause of these symptoms. Fuel pumps, hoses, tank vents, primer bulbs, filters, carburetors, and fuel fittings can create similar problems.
Why This Small Filter Matters
Fuel demand increases substantially as engine RPM and load increase.
A partially restricted screen may still pass enough fuel for the engine to idle or cruise normally, yet become a restriction when the engine is operated at higher RPM.
That can make the problem difficult to diagnose because the engine may appear perfectly healthy until it is placed under load.
For this reason, the fuel-pump filter screen should be inspected whenever a fuel-delivery problem is being diagnosed.
Key Features & Benefits
- Filters Incoming Fuel – Helps capture debris before it reaches the carburetors
- Supports Reliable Fuel Flow – A clean screen helps prevent restrictions in the fuel system
- Protects Carburetor Components – Reduces the chance of contamination reaching jets and passages
- Ideal for Fuel Pump Service – Easy component to inspect while the filter cap is removed
- Useful for Preventative Maintenance – Helps eliminate one possible source of fuel starvation
- Johnson/Evinrude OEM Application – Part number 312675 / 0312675
- Broad Application Range – Used across numerous OMC/Johnson/Evinrude fuel pump assemblies
Part Number & Application Information
- OEM Part Number: 312675
- Full OEM Number: 0312675
- Component: Fuel Pump Filter Screen
- Also Described As: Filter Cap Screen / Screen, Filter
- Typical Quantity: 1 per fuel pump assembly
OEM diagrams show 312675 used with components such as the filter cap and 330061 cap screw on many applicable fuel pump assemblies.
Common Applications
Part number 312675 has a very broad Johnson/Evinrude application history.
It appears in more than 100 OEM diagrams across multiple engine families and model years ranging from 35 HP to 125 HP.
Because the same screen was used in many different fuel-pump designs, always verify the engine model and OEM part number before ordering.
When Should Fuel Pump Filter Screen Be Replaced?
Replacement should be considered when:
- The screen is clogged
- The mesh is damaged
- The screen is distorted
- Heavy debris is present
- Fuel contamination has occurred
- The fuel pump is being rebuilt
- The filter cap is being serviced
- Fuel starvation is being diagnosed
- The existing screen is heavily stained or deteriorated
A screen that cannot be thoroughly cleaned or that shows physical damage should be replaced.
Inspect the Related Fuel Pump Components
Whenever the filter screen is removed, also inspect:
- Fuel pump cap
- Cap screw
- Cap gasket or O-ring
- Fuel inlet fitting
- Fuel pump diaphragm
- Fuel hoses
- Fuel tee fittings
Many applications pair the filter screen with the fuel pump cap screw, which secures the filter cap to the pump assembly.
If debris is found in the screen, it is also worth determining where that contamination came from instead of simply replacing the filter and ignoring the source.
Performance & Racing Considerations
For performance and racing outboards, fuel-system restriction can become much more noticeable at sustained high RPM.
An engine may idle and accelerate normally on the trailer or at lower speeds yet begin losing RPM once fuel demand increases.
At Liquid Revolutions, we know that small fuel-system components can create large troubleshooting headaches. Checking the Fuel Pump Filter Screen is a simple step that can help eliminate one possible cause of high RPM fuel starvation before moving on to carburetor jetting or ignition diagnostics.
Keeping the screen clean and in good condition helps support consistent fuel delivery and reliable engine performance.

